HOW TO RECEIVE

INTRODUCTION

KOSTKA is the first Czech satellite designed and built entirely by students, the work of the YSpace team at Brno University of Technology. It launched on 7 July 2026 and openly transmits telemetry in the 70 cm amateur band: status data that shows how the satellite is doing. You can receive it with an inexpensive USB radio and free software, and no special permission is needed to listen.



This guide covers the whole chain on a Windows computer and on an Android phone: hardware, antenna, software, finding a pass, tuning the receiver and decoding the packets. The two differ in one step: the telemetry is decoded by SoundModem, which runs only on Windows. On Android, you record the pass instead and decode it later on a PC.




KOSTKA is the first Czech satellite designed and built entirely by students, the work of the YSpace team at Brno University of Technology. It launched on 7 July 2026 and openly transmits telemetry in the 70 cm amateur band: status data that shows how the satellite is doing. You can receive it with an inexpensive USB radio and free software, and no special permission is needed to listen.



This guide covers the whole chain on a Windows computer and on an Android phone: hardware, antenna, software, finding a pass, tuning the receiver and decoding the packets. The two differ in one step: the telemetry is decoded by SoundModem, which runs only on Windows. On Android, you record the pass instead and decode it later on a PC.




Parameter

Parameter

Value

Value

Downlink frequency

Downlink frequency

436.870 MHz

436.870 MHz

Telemetry signal

Telemetry signal

9600 baud GFSK (G3RUH), AX.25 packets

9600 baud GFSK (G3RUH), AX.25 packets

Also on the same frequency

Also on the same frequency

Morse code (CW) beacon, packet digipeater

Morse code (CW) beacon, packet digipeater

Callsign

Callsign

OK0KST

OK0KST

NORAD catalog number

NORAD catalog number

69935

69935

Orbit

Orbit

Sun-synchronous low Earth orbit

Sun-synchronous low Earth orbit

LIVE FREQUENCIES AND STATUS

LIVE FREQUENCIES AND STATUS

SATNOGS DB

SATNOGS DB

SATNOGS DB

SATNOGS DB

The antenna catches the signal and the SDR dongle turns it into data for SDR++. SDR++ demodulates it into an audio signal, and SoundModem turns that audio into packets. Gpredict or Look4Sat tells you when KOSTKA is overhead and keeps SDR++ tuned while the satellite moves. This is needed because the satellite's speed shifts its frequency by up to about 10 kHz (the Doppler effect). 

The antenna catches the signal and the SDR dongle turns it into data for SDR++. SDR++ demodulates it into an audio signal, and SoundModem turns that audio into packets. Gpredict or Look4Sat tells you when KOSTKA is overhead and keeps SDR++ tuned while the satellite moves. This is needed because the satellite's speed shifts its frequency by up to about 10 kHz (the Doppler effect). 

Gpredict or Look4Sat retunes SDR++ through its Rigctl Server. On Android, the recording is decoded later with SoundModem on a Windows PC. 

Gpredict or Look4Sat retunes SDR++ through its Rigctl Server. On Android, the recording is decoded later with SoundModem on a Windows PC. 

SECTIONS

SECTIONS

Hardware components

You need four things: an SDR receiver, an antenna for the 70 cm band, a cable between them, and a Windows computer or an Android phone. 

You need four things: an SDR receiver, an antenna for the 70 cm band, a cable between them, and a Windows computer or an Android phone. 

Item

Item

What to get

What to get

Why

Why

SDR receiver

SDR receiver

An RTL-SDR dongle such as the RTL-SDR Blog V4, or a HackRF One or similar

An RTL-SDR dongle such as the RTL-SDR Blog V4, or a HackRF One or similar

A USB radio that covers 436.870 MHz

A USB radio that covers 436.870 MHz

Antenna

Antenna

An antenna made for 70 cm (435 to 438 MHz)

An antenna made for 70 cm (435 to 438 MHz)

Covered in the next section

Covered in the next section

Coaxial cable

Coaxial cable

As short as practical, with the right connector for your dongle

As short as practical, with the right connector for your dongle

Every metre of cable loses some signal

Every metre of cable loses some signal

Windows computer

Windows computer

A 64-bit Windows 10 or 11 PC or laptop

A 64-bit Windows 10 or 11 PC or laptop

Runs the whole chain, including decoding

Runs the whole chain, including decoding

Android phone or tablet

Android phone or tablet

Android 9 or newer, plus a USB OTG adapter (for example USB-C to USB-A)

Android 9 or newer, plus a USB OTG adapter (for example USB-C to USB-A)

Receives and records the pass for decoding on a PC

Receives and records the pass for decoding on a PC

Optional: LNA

Optional: LNA

A low-noise amplifier mounted close to the antenna

A low-noise amplifier mounted close to the antenna

Makes up for cable losses on longer runs

Makes up for cable losses on longer runs

Tips:


  • On Android, a powered USB hub between the phone and the dongle gives more stable reception.

  • Many dongles can power an LNA through the cable (the Bias-T option in SDR++). Switch it on only when a device that needs power is connected, or you risk damaging the hardware.

  • A short USB extension cable keeps the dongle away from the computer, which can reduce interference.

Tips:


  • On Android, a powered USB hub between the phone and the dongle gives more stable reception.

  • Many dongles can power an LNA through the cable (the Bias-T option in SDR++). Switch it on only when a device that needs power is connected, or you risk damaging the hardware.

  • A short USB extension cable keeps the dongle away from the computer, which can reduce interference.

Types of antennas

The antenna matters more than any other part, but a simple one is enough to start. 

The antenna matters more than any other part, but a simple one is enough to start. 

Antenna

Antenna

What it is

What it is

Best for

Best for

V-dipole

V-dipole

Two rods, each about 17 cm long, opened to about 120° and mounted horizontally

Two rods, each about 17 cm long, opened to about 120° and mounted horizontally

First attempts; cheap and easy to build

First attempts; cheap and easy to build

Turnstile or QFH (quadrifilar helix)

Turnstile or QFH (quadrifilar helix)

Fixed antennas that hear the whole sky

Fixed antennas that hear the whole sky

A permanent setup on a roof or balcony

A permanent setup on a roof or balcony

Handheld Yagi

Handheld Yagi

A directional antenna you point at the satellite by hand

A directional antenna you point at the satellite by hand

Stronger signals; follow the satellite using Look4Sat’s radar or Gpredict’s polar view

Stronger signals; follow the satellite using Look4Sat’s radar or Gpredict’s polar view

Yagi on a rotator

Yagi on a rotator

A directional antenna turned by a motor that follows the satellite

A directional antenna turned by a motor that follows the satellite

The strongest signals; needs a rotator and control software

The strongest signals; needs a rotator and control software

Tips: 


  • Put the antenna outdoors with as much open sky as possible. Indoors, the signal is much weaker. 

  • Avoid vertical whips and ground planes. They hear very little from straight overhead, where a pass is strongest. 

  • The low parts of a pass are weaker and often blocked by buildings and trees. 

  • Keep the cable short. If it has to be long, use low-loss cable or add an LNA at the antenna. 

Tips: 


  • Put the antenna outdoors with as much open sky as possible. Indoors, the signal is much weaker. 

  • Avoid vertical whips and ground planes. They hear very little from straight overhead, where a pass is strongest. 

  • The low parts of a pass are weaker and often blocked by buildings and trees. 

  • Keep the cable short. If it has to be long, use low-loss cable or add an LNA at the antenna. 

Software

All the programs are free. Install them before your first pass. 

All the programs are free. Install them before your first pass. 

Task

Task

Windows

Windows

Android

Android

Find out when KOSTKA flies over

Find out when KOSTKA flies over

Gpredict

Gpredict

Look4Sat

Look4Sat

Receive the signal

Receive the signal

SDR++

SDR++

SDR++

SDR++

Keep the receiver tuned during a pass

Keep the receiver tuned during a pass

Gpredict tunes SDR++

Gpredict tunes SDR++

Look4Sat tunes SDR++

Look4Sat tunes SDR++

Turn the signal into packets

Turn the signal into packets

HS SoundModem

HS SoundModem

Record in SDR++, decode later on a Windows PC

Record in SDR++, decode later on a Windows PC

Helpers

Helpers

Zadig (USB driver), VB-CABLE (virtual audio cable)

Zadig (USB driver), VB-CABLE (virtual audio cable)

None needed

None needed

Windows 


  1. Zadig, the driver for the dongle. Download zadig-2.9.exe from zadig.akeo.ie, plug in the dongle and run Zadig. Choose Options → List All Devices and select "Bulk-In, Interface (Interface 0)"; some systems show "RTL2832U" or "Blog V4" instead. Check that WinUSB is shown on the right, then click Replace Driver. 


  1. SDR++. Download sdrpp_windows_x64.zip from the SDR++ nightly release, unzip it to a folder such as C:\SDRPP and run sdrpp.exe. If Windows reports a missing DLL, install the Microsoft Visual C++ Redistributable. 


  1. VB-CABLE. Download it from vb-audio.com/Cable, unzip it, run the setup as administrator and restart the computer. It adds a virtual cable: sound played into "CABLE Input" comes out of "CABLE Output". 


  1. HS SoundModem. Download the newest hs_soundmodem zip (currently hs_soundmodem27.zip) from UZ7HO's packet radio page and unzip it. This high-speed version decodes 9600 baud G3RUH; the plain SoundModem does not. 


  1. Gpredict. Download gpredict-win32-2.3.37.zip from Gpredict release v2.3, unzip it and run gpredict.exe. It is the newest Windows build; later releases have no ready-made Windows download. 


Windows SmartScreen may warn about an unrecognised app when you first start these programs. Click More info, then Run anyway. 



Android 


  1. SDR++. Download sdrpp.apk from the SDR++ nightly release and open it on the phone. Allow installing apps from this source when Android asks. SDR++ needs Android 9 or newer. 


  1. Look4Sat. Install it from Google Play or F-Droid. 


  1. First start. Connect the dongle through the OTG adapter before you open SDR++, then allow access to the USB device and storage. SDR++ has the RTL-SDR driver built in, so no separate driver app is needed. 


Windows 


  1. Zadig, the driver for the dongle. Download zadig-2.9.exe from zadig.akeo.ie, plug in the dongle and run Zadig. Choose Options → List All Devices and select "Bulk-In, Interface (Interface 0)"; some systems show "RTL2832U" or "Blog V4" instead. Check that WinUSB is shown on the right, then click Replace Driver. 


  1. SDR++. Download sdrpp_windows_x64.zip from the SDR++ nightly release, unzip it to a folder such as C:\SDRPP and run sdrpp.exe. If Windows reports a missing DLL, install the Microsoft Visual C++ Redistributable. 


  1. VB-CABLE. Download it from vb-audio.com/Cable, unzip it, run the setup as administrator and restart the computer. It adds a virtual cable: sound played into "CABLE Input" comes out of "CABLE Output". 


  1. HS SoundModem. Download the newest hs_soundmodem zip (currently hs_soundmodem27.zip) from UZ7HO's packet radio page and unzip it. This high-speed version decodes 9600 baud G3RUH; the plain SoundModem does not. 


  1. Gpredict. Download gpredict-win32-2.3.37.zip from Gpredict release v2.3, unzip it and run gpredict.exe. It is the newest Windows build; later releases have no ready-made Windows download. 


Windows SmartScreen may warn about an unrecognised app when you first start these programs. Click More info, then Run anyway. 



Android 


  1. SDR++. Download sdrpp.apk from the SDR++ nightly release and open it on the phone. Allow installing apps from this source when Android asks. SDR++ needs Android 9 or newer. 


  1. Look4Sat. Install it from Google Play or F-Droid. 


  1. First start. Connect the dongle through the OTG adapter before you open SDR++, then allow access to the USB device and storage. SDR++ has the RTL-SDR driver built in, so no separate driver app is needed. 


SDR configuration


Source


Source

Setting

Setting

Value

Value

Source

Source

RTL-SDR, with your dongle selected

RTL-SDR, with your dongle selected

Sample rate

Sample rate

250 kHz, the lowest setting. KOSTKA’s signal fits easily, and a narrower span lets in less noise and eases the load on a phone

250 kHz, the lowest setting. KOSTKA’s signal fits easily, and a narrower span lets in less noise and eases the load on a phone

Gain

Gain

Start in the middle of the range, then adjust (see below)

Start in the middle of the range, then adjust (see below)

RTL AGC and Tuner AGC

RTL AGC and Tuner AGC

Off

Off

Bias-T

Bias-T

On only if an LNA or another powered device is connected

On only if an LNA or another powered device is connected

Press the Play button at the top left to start the receiver. 

Press the Play button at the top left to start the receiver. 


Radio


Radio

Setting

Setting

Value

Value

Frequency

Frequency

436.870 MHz, entered in the frequency display at the top

436.870 MHz, entered in the frequency display at the top

Mode

Mode

NFM

NFM

Bandwidth

Bandwidth

20000 Hz (20 kHz)

20000 Hz (20 kHz)

De-emphasis

De-emphasis

None

None

Squelch

Squelch

Off

Off

IF Noise Reduction

IF Noise Reduction

Off

Off

High Pass

High Pass

Off

Off

Low Pass

Low Pass

Off

Off

Sinks (where the sound goes) 


  • Windows: for the Radio stream choose Audio, set the device to "CABLE Input (VB-Audio Virtual Cable)" and the sample rate to 48000. SoundModem listens on the other end of the cable. 

  • Android: leave the sound on the phone's speaker so you can listen. The Recorder saves the signal for decoding, as described in the Decoding section.


Gain and volume 


Raise the gain until the background noise on the waterfall lifts slightly, then stop. Too much gain lets strong local signals overload the dongle, which shows up as false signals across the spectrum. 


SoundModem decodes only when the audio level is right: too quiet or too loud and it fails. Start with the SDR++ volume at about half, then fine-tune it during a pass. 


During a pass, KOSTKA's packets appear on the waterfall as short bursts near 436.870 MHz and sound like brief bursts of noise. 

Sinks (where the sound goes) 


  • Windows: for the Radio stream choose Audio, set the device to "CABLE Input (VB-Audio Virtual Cable)" and the sample rate to 48000. SoundModem listens on the other end of the cable. 

  • Android: leave the sound on the phone's speaker so you can listen. The Recorder saves the signal for decoding, as described in the Decoding section.


Gain and volume 


Raise the gain until the background noise on the waterfall lifts slightly, then stop. Too much gain lets strong local signals overload the dongle, which shows up as false signals across the spectrum. 


SoundModem decodes only when the audio level is right: too quiet or too loud and it fails. Start with the SDR++ volume at about half, then fine-tune it during a pass. 


During a pass, KOSTKA's packets appear on the waterfall as short bursts near 436.870 MHz and sound like brief bursts of noise. 

Pass predicitions


KOSTKA is in range only for a few minutes at a time, when it passes over your location. Prediction software tells you when a pass starts and ends, where in the sky to look and how high the satellite climbs. Because KOSTKA is in a sun-synchronous orbit, its passes come at similar local times every day. 


Start with passes that climb at least 30° above the horizon. The satellite is closer then, so the signal is stronger. 


KOSTKA is in range only for a few minutes at a time, when it passes over your location. Prediction software tells you when a pass starts and ends, where in the sky to look and how high the satellite climbs. Because KOSTKA is in a sun-synchronous orbit, its passes come at similar local times every day. 


Start with passes that climb at least 30° above the horizon. The satellite is closer then, so the signal is stronger. 


Windows: Gpredict 


  1. Set your location. Open Edit → Preferences → General → Ground Stations and click Add new. Enter a name and your coordinates or QTH locator, then make it the default. 


  1. Download the data. Run Edit → Update TLE data from network, then Edit → Update transponder data. The second step loads KOSTKA's frequencies from SatNOGS. 


  1. Create a module. Choose File → New module and name it KOSTKA. Search for KOSTKA or 69935, add it to Selected Satellites and pick your ground station. 


  1. Optional: add KOSTKA by hand. KOSTKA should already be in the CelesTrak lists that Gpredict loads by default. If the search in step 3 finds nothing, open Edit → Preferences → General → TLE Update, click Add TLE source and paste `https://celestrak.org/NORAD/elements/gp.php?CATNR=69935&FORMAT=tle`. Then run Edit → Update TLE data from network again. 


  1. See the passes. Right-click KOSTKA in the module and choose Future passes. Double-click a pass to open its details; the Polar tab shows its path across your sky. 



Android: Look4Sat 


  1. Set your location. In Settings → Station position, tap GPS, or enter your QTH locator. 


  1. Download the data. In Settings → Satellite data, tap Update. Look4Sat loads orbits and frequencies from CelesTrak and SatNOGS. 


  1. Select KOSTKA. Open Satellites, search for KOSTKA or 69935 and select it. 


  1. See the passes. Open Passes. Tap a pass to open the Radar, which shows where KOSTKA is in the sky and lists its transceivers. 


Orbit predictions slowly drift, so update the data about once a week in either program. 


Windows: Gpredict 


  1. Set your location. Open Edit → Preferences → General → Ground Stations and click Add new. Enter a name and your coordinates or QTH locator, then make it the default. 


  1. Download the data. Run Edit → Update TLE data from network, then Edit → Update transponder data. The second step loads KOSTKA's frequencies from SatNOGS. 


  1. Create a module. Choose File → New module and name it KOSTKA. Search for KOSTKA or 69935, add it to Selected Satellites and pick your ground station. 


  1. Optional: add KOSTKA by hand. KOSTKA should already be in the CelesTrak lists that Gpredict loads by default. If the search in step 3 finds nothing, open Edit → Preferences → General → TLE Update, click Add TLE source and paste `https://celestrak.org/NORAD/elements/gp.php?CATNR=69935&FORMAT=tle`. Then run Edit → Update TLE data from network again. 


  1. See the passes. Right-click KOSTKA in the module and choose Future passes. Double-click a pass to open its details; the Polar tab shows its path across your sky. 



Android: Look4Sat 


  1. Set your location. In Settings → Station position, tap GPS, or enter your QTH locator. 


  1. Download the data. In Settings → Satellite data, tap Update. Look4Sat loads orbits and frequencies from CelesTrak and SatNOGS. 


  1. Select KOSTKA. Open Satellites, search for KOSTKA or 69935 and select it. 


  1. See the passes. Open Passes. Tap a pass to open the Radar, which shows where KOSTKA is in the sky and lists its transceivers. 


Orbit predictions slowly drift, so update the data about once a week in either program. 

Doppler compensation and rotator control 

KOSTKA moves at about 7.6 km/s, so its frequency shifts during a pass, like the pitch of a passing ambulance siren. The signal starts up to about 10 kHz above 436.870 MHz and ends up to about 10 kHz below it. Without correction it drifts out of the 20 kHz filter, so let the prediction program retune SDR++ continuously. 

KOSTKA moves at about 7.6 km/s, so its frequency shifts during a pass, like the pitch of a passing ambulance siren. The signal starts up to about 10 kHz above 436.870 MHz and ends up to about 10 kHz below it. Without correction it drifts out of the 20 kHz filter, so let the prediction program retune SDR++ continuously. 


Radio


Radio

Setting

Setting

Value

Value

Frequency

Frequency

436.870 MHz, entered in the frequency display at the top

436.870 MHz, entered in the frequency display at the top

Mode

Mode

NFM

NFM

Bandwidth

Bandwidth

20000 Hz (20 kHz)

20000 Hz (20 kHz)

De-emphasis

De-emphasis

None

None

Squelch

Squelch

Off

Off

IF Noise Reduction

IF Noise Reduction

Off

Off

High Pass

High Pass

Off

Off

Low Pass

Low Pass

Off

Off

Step 1: allow remote tuning in SDR++ (Windows and Android) 


Open the Rigctl Server panel in the SDR++ menu. Keep the host localhost and port 4532, set Controlled VFO to Radio, tick Tuning and click Start. The status changes from Idle to Listening, and to Connected once a program takes control. Tick Listen on startup so the server starts with SDR++ next time. Are you planning to call 


Step 2 on Windows: Gpredict tunes SDR++ 


  1. In Edit → Preferences → Interfaces → Radios, click Add new. Enter a name such as SDR++, host localhost, port 4532 and radio type RX only. 


  1. In the KOSTKA module, open the module menu (the small arrow in the module's top-right corner) and choose Radio Control. 


  1. Select KOSTKA and its KOSTKA UHF AX.25 transponder, then click Track. If no transponder is listed, set the downlink frequency to 436.870 MHz with the mouse wheel over its digits. 


  1. Select your SDR++ radio as the device and click Engage. SDR++ now follows the Doppler shift by itself. 


Step 2 on Android: Look4Sat tunes SDR++ 


  1. In Look4Sat, open Settings → Data output → Network. Switch on Enable frequency output and keep IP:Port 127.0.0.1:4532 and the format F $FREQ. 


  1. Open the Radar for a KOSTKA pass and select the KOSTKA UHF AX.25 transceiver. Look4Sat keeps sending the corrected frequency to SDR++ while the Radar is open. If the Radar lists no transceivers for KOSTKA, frequency output cannot work, so tune by hand instead. 


  1. Show both apps in split-screen mode, so Android does not pause either of them. 


Rotator control (optional) 


A Yagi on a computer-controlled rotator can follow KOSTKA automatically. Both programs send the pointing directions to Hamlib's rotctld, or to a controller that speaks the same protocol, usually on port 4533. 


  • Windows: add the rotator in Edit → Preferences → Interfaces → Rotators. Then choose Antenna Control in the module menu, select KOSTKA, click Track and Engage. 


  • Android: in Settings → Data output → Network, switch on Enable rotation output and enter the controller's IP:Port; the format is P $AZ $EL. A Bluetooth output is also available. 


Setting up rotctld depends on your rotator model; see the Hamlib project for details. 

Step 1: allow remote tuning in SDR++ (Windows and Android) 


Open the Rigctl Server panel in the SDR++ menu. Keep the host localhost and port 4532, set Controlled VFO to Radio, tick Tuning and click Start. The status changes from Idle to Listening, and to Connected once a program takes control. Tick Listen on startup so the server starts with SDR++ next time. Are you planning to call 


Step 2 on Windows: Gpredict tunes SDR++ 


  1. In Edit → Preferences → Interfaces → Radios, click Add new. Enter a name such as SDR++, host localhost, port 4532 and radio type RX only. 


  1. In the KOSTKA module, open the module menu (the small arrow in the module's top-right corner) and choose Radio Control. 


  1. Select KOSTKA and its KOSTKA UHF AX.25 transponder, then click Track. If no transponder is listed, set the downlink frequency to 436.870 MHz with the mouse wheel over its digits. 


  1. Select your SDR++ radio as the device and click Engage. SDR++ now follows the Doppler shift by itself. 


Step 2 on Android: Look4Sat tunes SDR++ 


  1. In Look4Sat, open Settings → Data output → Network. Switch on Enable frequency output and keep IP:Port 127.0.0.1:4532 and the format F $FREQ. 


  1. Open the Radar for a KOSTKA pass and select the KOSTKA UHF AX.25 transceiver. Look4Sat keeps sending the corrected frequency to SDR++ while the Radar is open. If the Radar lists no transceivers for KOSTKA, frequency output cannot work, so tune by hand instead. 


  1. Show both apps in split-screen mode, so Android does not pause either of them. 


Rotator control (optional) 


A Yagi on a computer-controlled rotator can follow KOSTKA automatically. Both programs send the pointing directions to Hamlib's rotctld, or to a controller that speaks the same protocol, usually on port 4533. 


  • Windows: add the rotator in Edit → Preferences → Interfaces → Rotators. Then choose Antenna Control in the module menu, select KOSTKA, click Track and Engage. 


  • Android: in Settings → Data output → Network, switch on Enable rotation output and enter the controller's IP:Port; the format is P $AZ $EL. A Bluetooth output is also available. 


Setting up rotctld depends on your rotator model; see the Hamlib project for details. 

Decoding

HS SoundModem turns the audio from SDR++ into AX.25 packets. On Windows it decodes live during the pass. On Android you record the pass and play the recording into SoundModem on a PC afterwards

HS SoundModem turns the audio from SDR++ into AX.25 packets. On Windows it decodes live during the pass. On Android you record the pass and play the recording into SoundModem on a PC afterwards

Windows: live decoding 


  1. Start SDR++ with its sink set to CABLE Input, then start SoundModem. 


  1. In SoundModem, open Settings → Devices. Set the input device to "CABLE Output (VB-Audio Virtual Cable)" and the RX sample rate to 48000, and leave Dual Channel unticked. 


  1. In the main window, choose FSK G3RUH 9600bd as the modem for channel A. 


  1. During the pass, watch SoundModem's waterfall. Decoded packets appear in the monitor window, and lines showing Fm OK0KST come from KOSTKA. 


KOSTKA's beacons are plain text in CSV format, so you can read the values directly in SoundModem's monitor window. What each value means, for example temperatures, voltages and battery charge, is explained on the KOSTKA telemetry beacons page. The public KOSTKA telemetry dashboard shows the values collected by the SatNOGS network. 


Android: record, then decode on a PC 


  1. In the SDR++ Recorder panel, select Audio and the WAV container. Check that the level meter does not reach the top. 


  1. Press Record shortly before the pass starts and Stop after it ends. The file is saved in the phone's internal storage, in the sdrpp/recordings folder. 


  1. Copy the file to a Windows PC and set up SoundModem as in steps 2 and 3 above. 


  1. Play the recording in an audio player that lets you choose the output device, such as VLC. In VLC, choose Audio → Audio Device → "CABLE Input (VB-Audio Virtual Cable)" and set the volume to 100%. 


SoundModem then decodes the recording as if the pass were live. If nothing decodes, play it again at a slightly lower or higher volume. The same method works for recordings made with SDR++ on Windows. . 


Receiving your first pass 


Once everything is installed, a pass takes about half an hour of your time. Times below count from the start of the pass. 


  1. Beforehand: update the orbit data and pick a pass that climbs above 30°. 


  1. 15 minutes before: connect the antenna and the dongle, start SDR++ and press Play. Check 436.870 MHz, NFM and a 20 kHz bandwidth. 


  1. 10 minutes before: start the Rigctl Server in SDR++. Then click Track and Engage in Gpredict's Radio Control, or open Look4Sat's Radar for the pass. 


  1. 5 minutes before: on Windows, start SoundModem and check that its waterfall shows noise. On Android, press Record in SDR++. 


  1. During the pass: watch for bursts near 436.870 MHz. With a handheld Yagi, point it where Gpredict's polar view or Look4Sat's Radar shows KOSTKA. 


  1. After the pass: stop the recording and look for lines with Fm OK0KST in SoundModem. 


Do not worry if the first pass brings only noise. Check the troubleshooting table below and try the next pass. 


Troubleshooting 


Windows: live decoding 


  1. Start SDR++ with its sink set to CABLE Input, then start SoundModem. 


  1. In SoundModem, open Settings → Devices. Set the input device to "CABLE Output (VB-Audio Virtual Cable)" and the RX sample rate to 48000, and leave Dual Channel unticked. 


  1. In the main window, choose FSK G3RUH 9600bd as the modem for channel A. 


  1. During the pass, watch SoundModem's waterfall. Decoded packets appear in the monitor window, and lines showing Fm OK0KST come from KOSTKA. 


KOSTKA's beacons are plain text in CSV format, so you can read the values directly in SoundModem's monitor window. What each value means, for example temperatures, voltages and battery charge, is explained on the KOSTKA telemetry beacons page. The public KOSTKA telemetry dashboard shows the values collected by the SatNOGS network. 


Android: record, then decode on a PC 


  1. In the SDR++ Recorder panel, select Audio and the WAV container. Check that the level meter does not reach the top. 


  1. Press Record shortly before the pass starts and Stop after it ends. The file is saved in the phone's internal storage, in the sdrpp/recordings folder. 


  1. Copy the file to a Windows PC and set up SoundModem as in steps 2 and 3 above. 


  1. Play the recording in an audio player that lets you choose the output device, such as VLC. In VLC, choose Audio → Audio Device → "CABLE Input (VB-Audio Virtual Cable)" and set the volume to 100%. 


SoundModem then decodes the recording as if the pass were live. If nothing decodes, play it again at a slightly lower or higher volume. The same method works for recordings made with SDR++ on Windows. . 


Receiving your first pass 


Once everything is installed, a pass takes about half an hour of your time. Times below count from the start of the pass. 


  1. Beforehand: update the orbit data and pick a pass that climbs above 30°. 


  1. 15 minutes before: connect the antenna and the dongle, start SDR++ and press Play. Check 436.870 MHz, NFM and a 20 kHz bandwidth. 


  1. 10 minutes before: start the Rigctl Server in SDR++. Then click Track and Engage in Gpredict's Radio Control, or open Look4Sat's Radar for the pass. 


  1. 5 minutes before: on Windows, start SoundModem and check that its waterfall shows noise. On Android, press Record in SDR++. 


  1. During the pass: watch for bursts near 436.870 MHz. With a handheld Yagi, point it where Gpredict's polar view or Look4Sat's Radar shows KOSTKA. 


  1. After the pass: stop the recording and look for lines with Fm OK0KST in SoundModem. 


Do not worry if the first pass brings only noise. Check the troubleshooting table below and try the next pass. 


Troubleshooting 


Problem

Problem

What to try

What to try

SDR++ on Windows does not find the dongle

SDR++ on Windows does not find the dongle

Install the WinUSB driver with Zadig, as in the Software section, then restart SDR++

Install the WinUSB driver with Zadig, as in the Software section, then restart SDR++

SDR++ on Android does not find the dongle

SDR++ on Android does not find the dongle

Connect the dongle before starting SDR++. Close and reopen the app a couple of times; after reconnecting the dongle, press refresh in the Source panel

Connect the dongle before starting SDR++. Close and reopen the app a couple of times; after reconnecting the dongle, press refresh in the Source panel

Nothing appears on the waterfall during a pass

Nothing appears on the waterfall during a pass

Update the orbit data and check the clock on your device. Check the antenna and cable, and try a higher pass

Update the orbit data and check the clock on your device. Check the antenna and cable, and try a higher pass

The signal slides out of the filter

The signal slides out of the filter

Doppler control is not running: the Rigctl Server status should read Connected

Doppler control is not running: the Rigctl Server status should read Connected

The signal sits a few kHz from where it should be

The signal sits a few kHz from where it should be

Dongles without a TCXO can be off frequency; set PPM Correction in the Source panel

Dongles without a TCXO can be off frequency; set PPM Correction in the Source panel

The signal is clear but nothing decodes

The signal is clear but nothing decodes

Check that SoundModem uses CABLE Output and FSK G3RUH 9600bd, and that all filters in SDR++ are off. Adjust the SDR++ volume, try a 25 kHz bandwidth, or move SoundModem’s DCD slider

Check that SoundModem uses CABLE Output and FSK G3RUH 9600bd, and that all filters in SDR++ are off. Adjust the SDR++ volume, try a 25 kHz bandwidth, or move SoundModem’s DCD slider

Gpredict cannot update data from the network

Gpredict cannot update data from the network

Open the CelesTrak link from the Pass predictions section in a browser and save the text as kostka.txt in an empty folder. Then use Edit → Update TLE data from local files and select that folder

Open the CelesTrak link from the Pass predictions section in a browser and save the text as kostka.txt in an empty folder. Then use Edit → Update TLE data from local files and select that folder

Look4Sat does not tune SDR++

Look4Sat does not tune SDR++

Check Enable frequency output and 127.0.0.1:4532, select the transceiver in the Radar and start the Rigctl Server

Check Enable frequency output and 127.0.0.1:4532, select the transceiver in the Radar and start the Rigctl Server

SDR++ stops in the background on Android

SDR++ stops in the background on Android

Use split screen and turn off battery optimisation for SDR++

Use split screen and turn off battery optimisation for SDR++

HOW TO RECEIVE

First Czech university team focused on satellite development.

© 2026 | All rights reserved | Website made by Damian Knoth

Website made in Framer

First Czech university team focused on satellite development.

© 2026 | All rights reserved | Website made by Damian Knoth

Website made in Framer

First Czech university team focused on satellite development.

© 2026 | All rights reserved | Website made by Damian Knoth

Website made in Framer

First Czech university team focused on satellite development.

© 2026 | All rights reserved | Website made by Damian Knoth

Website made in Framer